Month: August 2022

The Bang & Olufsen Beosound 1 unit brought in with…

The Bang & Olufsen Beosound 1 unit brought in with…

The Bang & Olufsen Beosound 1 unit brought in with a failed SMPS found its way back on the bench today. The owner decided not to proceed with this repair & to dispose of the unit. Not liking to throw things away I have undertaken the repair of the SMPS board as a challenge 🙄. […]

Vonyx active speaker now has a replacement 12″ dri…

Vonyx active speaker now has a replacement 12″ dri…

Vonyx active speaker now has a replacement 12″ driver. This 350W SoundLAB driver is definitely an improvement on the manufacturer installed driver that physically fell apart 😔. #bridgnorthbusiness #shropshirebusiness#guitartech #amplifierrepair #audiorepair #audioservice #vonyxspeakers #activespeakers #djspeaker #djspeakersystem View this post on Facebook

The Laney GH50L is back to perfect health Power t…

The Laney GH50L is back to perfect health Power t…

The Laney GH50L is back to perfect health Power tube sockets replaced to restore the heater functionality, put a pair of ceramic ones in. Post power section repair, the three preamp tubes were found to be the cause of excessive noise & poor sound so they were replaced too. Power tube bias was way too […]

The lithium battery pack that came in with no outp…

The lithium battery pack that came in with no outp…

The lithium battery pack that came in with no output & refusal to charge has now had the issue diagnosed. Cutting open the sleeving to expose the battery management board revealed a broken wire. In the charger connector this wire is looped to the negative lead & inside the battery goes to the management controller. […]

Fender Telecaster with new pickup selector install…

Fender Telecaster with new pickup selector install…

Fender Telecaster with new pickup selector installed,pots cleaned, frets polished & restrung with D’Addario XL10-46. Customer requested that the string height remain as supplied but intonation was corrected. #bridgnorthbusiness #shropshirebusiness#guitartech #guitarrepair #guitarsetup #guitarservice #guitar #fender #fendertelecaster #guitartech #fenderguitars #dadarriostrings View this post on Facebook

Vonyx SPJ1200-A dropped off today with a non funct…

Vonyx SPJ1200-A dropped off today with a non funct…

Vonyx SPJ1200-A dropped off today with a non functional 12″ driver. Checking the cone for impeded movement, usually a sign of voice coil damage, it was apparent that the cone could not move freely. As the unit powered correctly & passed sound from the HF unit the amplifier board showed as functional. Connecting one of […]

The Laney GH50L head brought in non functioning wi…

The Laney GH50L head brought in non functioning wi…

The Laney GH50L head brought in non functioning with only one output tube having a working heater filament, now has a new pair of ceramic octal bases. The EL34s installed by the owner were a new matched pair. The switch on the rear for EL34 / 6L6 bias was in the correct position for the […]

The Pioneer XDJ-700 has now had the cue & play but…

The Pioneer XDJ-700 has now had the cue & play but…

The Pioneer XDJ-700 has now had the cue & play button actuators & the micro switches below replaced. Quite expensive parts at a fraction under £30 for a plastic molding & a pair of 50pence micro switches 😔 but an essential repair for the unit to be used reliably. Apparently a very common issue arising […]

Fender Telecaster in for some electrical repairs, …

Fender Telecaster in for some electrical repairs, …

Fender Telecaster in for some electrical repairs, a restring & fret polish. #bridgnorthbusiness #shropshirebusiness#guitartech #guitarrepair #guitarsetup #guitarservice #guitar #fender #fendertelecaster #telecaster #guitarwiring #guitartechworks View this post on Facebook

The Pioneer XDJ-700 is now disassembled revealing …

The Pioneer XDJ-700 is now disassembled revealing …

The Pioneer XDJ-700 is now disassembled revealing the root cause of the issue being a broken button actuator molding. A quick Google search for a replacement reveals this to be an extremely common issue & not only on this particular model. The switches appear to be functioning correctly but dripped a spot of switch cleaner […]

× How can I help you?